Category Archives: laying

Technology of Placing gypsum tiles with your own hands

Gypsum tiles must be laid properly, as not only the aesthetic look of decorative facing, but in addition the service quality of

the material will be based on the engineering of job. The product is more also universal, and it can be attached to concrete,

plaster, brick or gypsum board sheets, and provided that the surface of the base is and has no defects.

In the event the flaws of this base are important, it should be thoroughly treated with primer, then a cement mortar is made,

which satisfies all of the cracks. Then the surface should be repeatedly primed and dried. Primer treatment is necessary to

improve the bond between the tile and the wall. In cases like this, its makeup should pick a special, comprising components that

prevent the appearance of fungus and mould.

In today’s interior of these rooms most frequently used gypsum tiles, imitating natural brick or stone. To carry out decorative

finishing yourself, it is necessary firstly to select a strategy of tile positioning and prepare a solution. It’s necessary to

focus on the reverse side of this material. When its surface includes an embossed surface, then the adhesive should be placed with

an trowel, also if it is even, then with a top notch one.

The tech of the job is as follows:

* A thin coating of adhesive mortar is put on the pre-prepared wall. It’s spread over the foundation so it is likely to put 4-5

tiles. Decorative cladding may be put either on plasterboard, and on putty.

* Cover the rear side of the tiles with adhesive.

* Plaster elements are pressed against the wall and their location is adjusted. To align the seams, it is advised to use


* Finishing is carried out in rows, all which ought to be shifted by half of a tile. Facing is carried out into the corners of

this room, and then immediately eliminate any residual mortar in the joints.

Drying the walls requires no more than a day also needs a constant humidity and temperature inside the room. The last stage in the

laying of gypsum tiles is the decor. To get this done, the joints between the elements are filled with a particular solution, the

shade of which matches the brick.

Cosmetic fake of brickwork on the walls has been completed in the following ways:

* Cutting on the surface of the pits of masonry with a bolt cutter with your hands;

* placing of tiles beneath the brick:

* mimicking the format and color of the side of a single brick;

* Imitating a fragment of brickwork of many bricks.

The perfect method to decorate”under the brick” would be the one which enables you to create a usable coating with the maximum

appearance of its similarity to organic masonry. All three ways to conduct this sort of finishing works meet the requirements,

however, the cutting edge of joints with a bolt is more labor-intensive along with the formation of considerable amounts of dust,

and so let’s consider more prevalent manners.

The old finish is removed from the walls, and the surface, if necessary, is leveled to get rid of the need to glue plaster on a

thick layer of glue.

Combining these cladding with other kinds of interior finishes may be both systematic and done without any apparent consequences,

chaotically, with imitation of signs of aging.

With the support of cosmetic gypsum tiles it’s possible to mimic a lot of textures.

A large number of textures may be imitated with the help of cosmetic gypsum tiles.

The wall on which it’s to be set up should possess the following attributes:

* Hardness and intensity of the outside;

* The lack of uneven locations and sharp sections;

* not any deformations.

Decorative tiles at the interior of the kitchen

Walls are made from a number of substances, so let’s break down the principles of installment.

When dealing with concrete, there will not be any huge problems. It is only necessary to take into consideration the porosity of

this material. Concrete, which has almost no pronounced pores, ought to be treated with a good primer.

Mounting gypsum tiles on concrete

Before starting work on the setup of gypsum tiles onto the walls, it is worth checking the strength of their surface. After the

plaster doesn’t fall off the walls and at precisely the identical time holds well, it’s possible to simply paint it using primer.

Mount the tiles on the painted concrete should not. The surface ought to be scratched, making sure to misfire, then it needs to be

grouted and coated with a coating of plaster.